Construction precautions of shaped ceiling constru

2022-07-22
  • Detail

Modeling ceiling has become an increasingly popular ceiling material. We know that in many places, appearance design is very important, and modeling ceiling just conforms to this feature. Therefore, various high-end products have appeared one after another. What is the construction process of modeling ceiling, and how to install modeling ceiling? The following editor will introduce it to you

shaped ceiling has become an increasingly popular ceiling material. We know that in many places, appearance design is very important, and shaped ceiling just conforms to this feature. Therefore, various high-end products have emerged one after another. What is the construction process of shaped ceiling and how to install it? The following editor will introduce it to you

I. precautions for modeling ceiling construction

1. Before installation, you should go to the construction site to see if there are conditions to install the keel, which is mainly reflected in whether the wall body is completed, whether the carpentry is qualified, whether the plastering place is completed, and some dimensions of carpentry must be done according to the requirements

2. Before the installation of modeling ceiling, be sure to check whether the keel joint is firm and smooth. Handle the sealing part as above, and stick it on the sprinkler head with adhesive tape. When installing the shaped ceiling, fix it from the middle and both sides first, and pay attention to the installation size at the same time. The welding seam should be straight and the corner position should be well controlled. After the last four weeks, trim and remove the extra ceiling to make it beautiful in appearance

3. Perforated lamp: mark the lamp hole and stick the PVC lamp ring accurately to the bottom of the soft film. Remove the excess lace after fastening

4. If the conditions of the construction site permit, the carpenter according to the requirements of the design drawings should do some work to fix the PVC special keel, and the corners must be flat and smooth

5. Open the tuyere and light pipe opening: find the position of the tuyere and light pipe opening, which is the same as that of the surrounding area. Install the soft film on the PVC special keel, and pay attention to the flatness of the corner. Remove the extra smallpox after completion

6. Finally, clean the surface of the modeling ceiling with a clean towel

7. Note that the lamp holder, air outlet and light pipe panel should be level with the surrounding keel, and should be firm and stable without swinging

8. Smoke detector and ceiling lamp should be positioned first, and then a wooden underframe should be made. The bottom surface of the wooden underframe should be polished smooth, and pay attention to the horizontal height. If it is too low, it is easy to highlight the trace of the underframe

II. Modeling ceiling construction process

1. When installing the wavy shape, the wavy underframe of each keel should be consistent, so that the wavy shape can be neat and coordinated after the soft film is installed

2. The edge of the underframe in contact with the soft film must be smooth. After installation, the plastic ceiling, pull film ceiling, pull awning ceiling, flexible ceiling, transparent film, plastic ceiling, art ceiling, bathing ceiling will not be uneven

3. If there is a gap between the soft film and the soft film, when hoisting the underframe, the suspender and main keel should be made of thin materials as much as possible. Be hidden and tidy. Looking from bottom to top, the suspender fixing the underframe cannot be seen

4. Install plastic ceiling, pull film ceiling, pull Peng ceiling, flexible ceiling, transparent film, plastic ceiling, art ceiling, shower ceiling, which should be fully heated, especially in cold places, before disassembling the crystal cotton, in order to prevent the cold from making the soft film brittle and damaging the soft film

5. Install circular shaped ceiling, pull film ceiling, pull Peng ceiling, flexible ceiling, transparent film, plastic ceiling, art ceiling, shower ceiling, the flat code should be bent with a bending machine. The arc is smooth and there is no cutting seam

6. If the cutting method is used for bending, it must be cut every three centimeters, evenly, and cannot be cut more than half the thickness of the keel, otherwise prismatic shape will appear

7. If time permits, install the keel first, measure the size, and then place an order, which can reduce many quality problems caused by modification or inappropriate size

the relevant information about the construction precautions and construction technology of shaped ceiling is introduced here. I hope this article is helpful to you. If there is anything else you don't understand, you can leave a message to Xiaobian below, and we will answer it for you as soon as possible

living room ceiling design home decoration living room design effect drawing

living room decoration living room looks good without ceiling

gypsum board ceiling process gypsum ceiling decoration effect drawing

led ceiling lamp LED energy-saving lamp top ten brands ranking

杭州妇产医院

成都甲状腺医院

北京精神医院

Copyright © 2011 JIN SHI